|
| Our Products  Spray-On Equipment |
   |
 |
|
We handle the full line of
Graco/Glas-Craft products. |
|
|
Glas-Craft MH
(BEING
PHASED OUT)
PARTS
WILL STILL BE AVAILABLE
The MH can generate 3000 psi fluid pressure and necessary material
temperature to spray most all polyurea and polyurethane coatings.
Generating fluid pressure and maintaining that pressure while spraying –
are two different matters.
The MH is the top of the line polyurethane/polyurea machine for the
industrial applications and is a lower air consumption unit. Large fluid
section pumps 1 gallon in 16 strokes and has a capacity to pump over 5
gallons per minute. It relies on a hydraulic motor instead of a
pneumatic motor. A 50-foot heated hose assembly is standard on the MH unit. |
 |
Specifications:
• Max Output: 45 lb per min / 20 kg per
min
• MaxTemp:190ºF/88ºC
• Primary Heaters:
14,000 Watts (7000 watts per side)
• Max Pressure: 3000
PSI, 190 Bar
• Hose Size: 3/8” i.d. / 95 mm
• Length: 50 ft. Std / 300 Ft Max
• Heat: Copper-wound Hoses
• Heat Control: Solid-state LED Control
• Material Feed: Transfer Pumps
• Probler Gun: Round Spray 17254-xx or P2 23950-xx
Electrical Requirements:
3Phase 208VAC 63AMP 60Hz
3Phase 380VAC 63AMP 50Hz
Air Requirements:
15
cfm@100 psi 425 l/min@6.8 bar
|
| |
|
Glas-Craft MH II
(BEING
PHASED OUT)
PARTS
WILL STILL BE AVAILABLE
The MH II can generate 2500 psi fluid pressure and necessary material temperature to spray most all polyurea and polyurethane coatings. Generating fluid pressure and maintaining that pressure while spraying – are two different matters.
The MH II will have a very low pressure drop when you pull the trigger –
giving you the require mixing pressure at the gun where needed – not
just static pressure. | |
 |
Specifications:
• Max Output: 22 lb per min / 10 kg per min
• Max Temp: 190º F / 88º C
• Primary Heaters: 6000 Watts
• Max Pressure: 2200/3000 PSI, 150/204 Bar
• Hose Size: 3/8” i.d. / 95 mm
• Length: 50 ft. Std / 300 Ft Max
• Heat: Copper-wound Hoses
• Heat Control: Solid-state LED Control
• Material Feed: Transfer Pumps
• Probler Gun: Round Spray 17254-xx or P2 23950-xx
Electrical Requirements:
74 amp / 208/240 V VAC AC Single Phase Phase, , 60 Hz 40 amp / 208/240 V VAC AC Three Phase Phase, , 60 Hz 40 amp / 380 V VAC AC Three Phase Phase, , 50 Hz
Air Requirements:
15 cfm@100 psi 425 l/min@6.8 bar |
|
Glas-Craft MH III
(BEING
PHASED OUT)
PARTS
WILL STILL BE AVAILABLE
The Glas-Craft MH III Dispensing System is a hydraulically driven system, designed for use in house or in a field location. The MH III is the top of the line polyurethane/polyurea machine for the bedliner and is a lower air consumption unit. It relies on a hydraulic motor instead of a pneumatic motor. A 50-foot heated hose assembly is standard on the MH III unit. | |
 |
Specifications:
• Max Output: 22 lb per min / 10 kg per min
• Max Temp: 190º F / 88º C
• Primary Heaters: 10000 Watts
• Max Pressure: 3000 PSI / 204 Bar
• Hose Size: 3/8” i.d. / 95 mm
• Length: 50 ft. Std / 310 Ft Max
• Length: 10 ft. Heated Whip
• Heat: Copper-wound Hoses
• Heat Control: Solid-state LED Control
• Material Feed: Transfer Pumps
• Probler Gun: Round Spray 17254-xx or P2 23950-xx
Electrical Requirements:
74 amp, 208-240 VAC, single phase, 60Hz.
50 amp, 208-240 VAC, three phase, 60Hz.
40 amp, 380 VAC, three phase 50/60 Hz.
Air Requirements:
15 cfm @100 psi / 425 l/min @ 6.8 bar
|
|
Guardian A6
6000/12000
The Guardian A6 Dispensing System is a pneumatic system, designed
for use in house or in a field location. The Guardian A6 is the top of the line polyurea machine for the bedliner
and industrial applications. The design of the Guardian air motor
delivers efficient, consistent trouble free operation. The Guardian
A6 comes from the factory with the Probler P2 gun, 50-foot heated
hose and 10' whip and is capable of handling up to 310' of total
hose. |
|
 |
Specifications:
• Max Output: 20 lb per min / 9 kg per min
• Max Temp: 190º F / 88º C
• Primary Heaters:
1. A6-6000 - 300 Watts per side (6000 watts total heat)
2. A6-12000 - 6000 Watts per side (12000 watts total heat)
• Max Pressure: 2200 / 3000 PSI
• Hose Size: 3/8” i.d. / 95 mm
• Length: 50 ft. Std / 310 Ft Max
• Length: 10 ft. Heated Whip
• Heat: Copper-wound Hoses
• Heat Control: Digital Controllers for Iso, Poly & Hose heat
• Material Feed: Transfer Pumps
• Gun: Round Spray Probler P2 23950-xx
Electrical Requirements
A6-6000
50amp 220 VAC, single phase, 50 / 60Hz
25 amp, 220 VAC, three phase, 50 / 60Hz.
25 amp, 380 VAC, three phase 50/60 Hz.
A6-12000
75
amp, 220 VAC, single phase, 50 / 60Hz.
35 amp, 208-240 VAC, three phase,
50 / 60Hz.
35 amp, 380 VAC, three phase 50/60 Hz.
Air Requirements:
33 cfm @100 psi /
834 l/min @ 6.8 bar (Includes transfer pumps) |
|
Probler Guns
Reliable... That's the proven Probler Gun. Rugged construction with fewer wear parts means a light-weight (three pounds), maneuverable gun that's tough on the job and easy on the operator. Continuous air purge eliminates sticking valve rods and associated downtime... No more constant triggering. Since the gun cannot be operated without the air purge being activated, an operator can stop, pick-up and start spraying again without danger of setting up the gun. Pistol-grip handle and full finger trigger have been designed to fit the hand for easy, comfortable spraying.
| |
 |
Versatile...
The
Probler spray gun adapts to most proportioners, so you can upgrade
your existing equipment by simply connecting a Probler Gun to assure
proper mixing and maximum yield. And what's more, Probler simplifies
your entire spray operation and saves you time and money because
it's the one gun that covers all output ranges. With Probler, the
one gun that does it all, you don't have to worry about several guns
and an inventory of spare parts for each.
Probler Gun Features:
• Angled hose connections
• Air shut-off valve
• Consistent spray pattern
• Air-actuated spray pattern
• Mixing chambers: round or flat spray
• Side block check valve assemblies
• Manual material shut-off valves
• High pressure airless mixing |
| 
The next generation in plural component spray guns Probler P² is here!
Place your order NOW!
Lightweight, Ergonomic Design Compact design makes it easy for operators to maneuver into difficult spray positions. Hardened Metal Mixing Chamber & Side Block Seals Longest lasting seals available.
Two Piece Mixing Chamber If a drill bit breaks off in the mixing chamber, you just replace the inexpensive snout - not the entire chamber. Check Valve Separating Liquid Portion of Gun from Dry Areas No more cleaning small air passages with tiny drill bits.
Dual Air Piston for Double the Triggering Force Over 300 psi of trigger force - you will not see sluggish chamber movement when you pull the trigger.
Grease Fitting on the Gun for Daily Lubrication You don't need to take the gun apart for daily service.
Individual Side Block Attachment to Gun. You will not need to line everything up or have a third hand to get side blocks attached to the gun Minimal Daily or Routine Maintenance Required You don't need to take the gun apart daily - or even weekly.
Probler P² can be used with either harden steel or standard plastic side block seals.
The New
Probler P²
Features:
● Smaller, lighter weight, & easier to use
● Better spray pattern
● Less overspray
● New duel piston air cylinder
● New two piece mixing chamber
● Fluid screens on both A and B side blocks
● steel side wipe seal option
● Grease fitting on the gun head
● New look
|
|
|
Graco Reactor A-20 | |
The Graco A-20 Dispensing System is a pneumatic system, designed
for use in house or in a field location. The Graco A-20 is the top of the line polyurea machine for the bedliners
and smaller projects. The design of the Graco A-20 air motor
delivers efficient, consistent trouble free operation. The Graco
A-20 comes from the factory with the Air-Purge Fusion gun, 50-foot heated
hose and 10' heated whip and is capable of handling up to 210' of total
hose. |
 |
Specifications:
Maximum output:
20 lbs / min (9.1 kg/min)
Maximum fluid working
pressure:
2,000 psi (138 bar, 13.8
MPa)
Maximum inlet air
pressure:
120 psi (8.3 bar, 0.83 MPa)
Air consumption @ 100
psi:
23 scfm (with Fusion® AP
AR4242)
System air consumption @
100 psi with 2:1 feed pumps:
28 scfm at flow rate listed
above
Maximum fluid
temperature:
190°F (88°C)
Maximum heater wattage:
6,000 watts
Maximum hose length (3/8
ID plus 1/4 ID whip hose):
210 ft (64 m)
Power requirements:
39A at 230V, 1-phase: 22A
at 230V, 3-phase: 14A at 380V, 3-phase (4-wire)
|
| |
The E series electric
motor provide superior efficiency and improved performance.
Pressure relief valves offer quick and easy balancing of system
pressures. The easy to service fluid sections reduce maintenance
increase productivity. The E series Reactor machines come with
high output heaters and depending on the machine can achieve
maximum temperatures of up to 15,300 watts. Digital heat and
pressure controls accurately program temperatures and pressures.
Balanced proportioning eliminates pressure fluctuations to give
you a consistent spray pattern. | |
Graco Reactor E-20 |
 |
Specifications:
Maximum output:
20 lbs / min (9.1 kg/min)
Maximum fluid working
pressure:
2,000 psi (138 bar, 13.8
MPa)
Maximum inlet air
pressure:
120 psi (8.3 bar, 0.83 MPa)
System air consumption @
100 psi with 2:1 feed pumps:
18 scfm at flow rate listed
above
Maximum fluid
temperature:
190°F (88°C)
Maximum heater wattage:
6,000 watts
Maximum hose length (3/8
ID plus 1/4 ID whip hose):
210 ft (64 m)
Power requirements:
48A at 230V, 1-phase: 32A
at 230V, 3-phase: 24A at 380V, 3-phase (4-wire)
|
| |
Graco Reactor E-30 |
 |
Specifications:
Maximum output:
30 lbs / min (13.5 kg/min)
Maximum fluid working
pressure:
2,000 psi (138 bar, 13.8
MPa)
Maximum inlet air
pressure:
120 psi (8.3 bar, 0.83 MPa)
System air consumption @
100 psi with 2:1 feed pumps:
18 scfm at flow rate listed
above
Maximum fluid
temperature:
190°F (88°C)
Maximum heater wattage:
10,200 or 15,300 watts
Maximum hose length (3/8
ID plus 1/4 ID whip hose):
310 ft (94 m)
Power requirements:
With 10.2 kW heater:
78A at 230V, 1-phase: 50A at 230V, 3-phase: 34A at 380V,
3-phase (4-wire)
With 15.3 kW heater:
100A at 230V, 1-phase: 62A at 230V, 3-phase: 35A at 380V,
3-phase (4-wire)
|
| |
Graco Reactor E-XP1 |
 |
Specifications:
Maximum output:
1 gpm (3.8 lpm)
Maximum fluid working
pressure:
2,500 psi (172 bar, 17.2
MPa)
Maximum inlet air
pressure:
120 psi (8.3 bar, 0.83 MPa)
System air consumption @
100 psi with 2:1 feed pumps:
18 scfm at flow rate listed
above
Maximum fluid
temperature:
190°F (88°C)
Maximum heater wattage:
10,200 watts
Maximum hose length (3/8
ID plus 1/4 ID whip hose):
210 ft (64 m)
Power requirements:
With 10.2 kW heater:
69A at 230V, 1-phase: 43A at 230V, 3-phase: 24A at 380V,
3-phase (4-wire)
|
| |
Graco Reactor E-XP2 |
|
|
Specifications:
Maximum output:
2 gpm (3.8 lpm)
Maximum fluid working
pressure:
3,500 psi (240 bar, 24.0 MPa)
Maximum inlet air
pressure:
120 psi (8.3 bar, 0.83 MPa)
System air consumption @
100 psi with 2:1 feed pumps:
18 scfm at flow rate listed
above
Maximum fluid
temperature:
190°F (88°C)
Maximum heater wattage:
15,300 watts
Maximum hose length (3/8
ID plus 1/4 ID whip hose):
310 ft (94 m)
Power requirements:
With 15.3 kW heater:
100A at 230V, 1-phase: 62A at 230V, 3-phase: 35A at 380V,
3-phase (4-wire)
|
|
|
Graco Reactor H-XP2 |
 |
Specifications:
Maximum output:
1.5 gpm (5.7 lpm)
Maximum fluid working
pressure:
3,500 psi (138 bar, 13.8 MPa)
Maximum inlet air
pressure:
120 psi (8.3 bar, 0.83 MPa)
System air consumption @
100 psi with 2:1 feed pumps:
28 scfm at flow rate listed
above
Maximum fluid
temperature:
190°F (88°C)
Maximum heater wattage:
15,300 watts
Maximum hose length (3/8
ID plus 1/4 ID whip hose):
310 ft (94 m)
Power requirements:
100A at 230V, 1-phase: 62A
at 230V, 3-phase: 35A at 380V, 3-phase (4-wire)
|
| |
Graco Reactor H-XP3 |
|
|
Specifications:
Maximum output:
2.5 gpm (9.5 lpm)
Maximum fluid working
pressure:
3,500 psi (240 bar, 24.0 MPa)
Maximum inlet air
pressure:
120 psi (8.3 bar, 0.83 MPa)
System air consumption @
100 psi with 2:1 feed pumps:
28 scfm at flow rate listed
above
Maximum fluid
temperature:
190°F (88°C)
Maximum heater wattage:
20,400 watts
Maximum hose length (3/8
ID plus 1/4 ID whip hose):
410 ft (64 m)
Power requirements:
90A
at 230V, 3-phase: 52A at 400V, 3-phase (4-wire)
|
| |
Graco Fusion Gun |
 |
Graco's Fusion
spray guns apply everything from polyurea and polyurethane
coatings to spray foam. The new Fusion guns are designed for
less maintenance and downtime, longer life and a better mix.
All this gives you optimal performance and high productivity
and makes Fusion the best plural-component spray gun you'll
ever use.
Pick one up and
experience the revolution!
Hand-tight
connections for easy servicing.
Available in
air, mechanical, solvent purge.
NOTE: All the Graco
Machines above come with the Graco Air Purge Fusion Gun.
|
| |
Graco Gap Pro Gun |
 |
Designed for
construction, bedliners, roofing and other plural-component
spraying.
Hardened steel
side seals and mix chamber for long-lasting performance
No adjustments
necessary
Easy access
screens reduce end-of-the-day maintenance time.
Easy to clean A
and B filters reduce downtime!
Low maintenance
fasteners are easy to remove with a standard nut-driver.
|
| | |
|
Back To Top |
|
|
